When a circuit goes dead or a panel starts behaving strangely, the size of the job is not always obvious from the outside. We handle the full range of electrical work in Kendall, from swapping out a single outlet to running new circuits through a house that has never been properly wired for modern loads. The call is where we figure out what the job actually involves, and the price is confirmed before anything is scheduled.
Homes across this area have every kind of panel and circuit in them. That range covers the full scope of what the work here involves. Whether the property is a single-family home, a rental unit, or a small commercial space, the process is the same: describe what is going on, get a straight answer on the scope, and move forward from there.
We take calls every day from 9:00 AM to 11:00 PM at (786) 926-3289.
Most calls start with a symptom, not a diagnosis. A breaker that will not stay reset. Lights that dim when the air conditioning kicks on. An outlet that stopped working for no obvious reason. Those symptoms are the starting point, and the job is to trace them back to their actual cause before any repair is quoted or started.
A Level 2 charger needs a dedicated 240-volt circuit, and the first question is whether the panel has room to carry it. If it does, we run the circuit to the garage or parking area and wire in the charger. If the panel is already at capacity, we talk through the upgrade path before anything is put on the calendar. The circuit is sized to the charger's draw and confirmed before the job closes.
Properties with irrigation systems or well pumps need dedicated circuits that can handle the motor load without pulling down the rest of the house. Grounding and bonding on these circuits matters, because the wiring runs outdoors and often into wet ground. We check the existing supply, confirm the circuit sizing is appropriate for the pump's draw, and run a new circuit when the existing one is not up to the job.
A dead outlet is sometimes a failed device. It is sometimes a tripped GFCI upstream that is protecting a chain of outlets the homeowner did not know were connected. It is occasionally a wiring fault behind the wall. The diagnostic step is what tells us which one it is, and we do that before quoting the repair. GFCI protection is required at every wet location, and AFCI protection has its own requirements in bedrooms and living areas. We install both where the code calls for them.
Aluminum branch-circuit wiring turns up in properties built during a specific period, and it requires specific connectors and terminations at every device rather than a simple replacement of the outlet. Knob-and-tube wiring is a different situation entirely and typically means pulling new copper branch circuits from the panel out. A partial rewire addresses the problem areas when the rest of the wiring is sound. A full rewire starts fresh. The inspection on the call or on-site is what determines which one applies.
A whole-home surge protector installs at the service entrance and catches voltage spikes before they reach the branch circuits. In this region, where lightning is a regular event during the long storm season, point-of-entry protection covers appliances, electronics, and the wiring itself. It works alongside individual point-of-use protection, not instead of it. We size the device to the service, confirm the grounding is solid, and explain what the system covers before the job is done.
A dimmer or smart switch is a straightforward replacement when the wiring behind the wall is already set up for it. When it is not, the job involves confirming the neutral is present, checking the load rating, and sometimes adjusting the wiring configuration at the box. Three-way switch setups add another step. We scope it on the call.
Some electrical work is simple to access. Some of it is behind a finished ceiling, inside an attic with low clearance, or in a crawl space that requires planning before anyone goes in.
Attic wiring runs in a part of the house that is hot, cramped, and not designed for regular foot traffic. When new circuits need to be run through an attic, or when existing wiring up there needs to be inspected or replaced, the job is planned around the access point and the conditions inside. We protect the finished surfaces below while we work, so what is above the ceiling stays above the ceiling.
Ceiling fan installation and fixture replacement on a vaulted or two-story ceiling is a different job from the same work at standard height. The access plan, the equipment needed, and the time involved all change. That is part of what gets talked through on the call, so the scope is accurate before anyone shows up.
Electrical pricing is not one-size-fits-all, and a quote that does not account for the actual situation is not a useful one. The price depends on what the fault turns out to be, what has to be opened up to reach it, and whether the existing circuit or panel can carry the change being asked of it.
A load calculation is part of scoping any job that adds to what the panel is already handling. A panel that is already at capacity changes the path for an EV charger circuit, a new appliance circuit, or a subpanel addition. A wiring type that requires specific handling, like aluminum branch-circuit wiring, changes the material and the method. All of that factors into the quote, and the quote is given on the call before anything is scheduled.
What you get when you call is a straight answer on what the job involves and what it will cost. If the scope changes on-site because something unexpected turns up behind the wall, we explain what changed before proceeding. Nothing is added without a conversation first. Most of the practical detail sits on our electrical repair services page.
In a condo or apartment, the unit's panel is often in a hallway closet, a utility room, or a dedicated electrical closet rather than a garage or basement. The breakers inside it control the branch circuits within the unit. The building's main service and common-area wiring are a separate system, and those are the building's responsibility rather than the individual unit's.
When an electrical problem in a unit traces back to shared infrastructure, the building's property manager or HOA is the right point of contact for that portion of the work. We handle what is inside the unit: the panel, the branch circuits, the outlets, switches, and fixtures. If the fault turns out to be upstream of the unit's panel, we can tell you that on the call or on-site so you know who to contact next.
Appointments in Kendall are arranged on the call. We confirm what the schedule allows and find a window that works for the property and the people in it. For rental properties with tenants, we work around occupancy. For businesses that need to stay open, we discuss what can be done without disrupting operations before the visit is booked.
When a problem will not keep, we take short-notice calls during our hours, every day from 9:00 AM to 11:00 PM. A sparking outlet, a panel that is buzzing and warm, or a circuit that will not reset are the kinds of situations that move to the front of the conversation.
Call (786) 926-3289, describe what is happening, and we will talk through it before anything else is decided.
Kendall is our primary focus on this page, but the coverage does not stop at the city line. We work throughout the surrounding communities in Miami-Dade County, including Sunset, Richmond Heights, The Crossings, Pinecrest, and Palmetto Estates. Residential work covers single-family homes, condos, and rental units. Commercial work includes small businesses, office spaces, and retail locations. The process is the same regardless of where the property sits: scope the job on the call, confirm the price, and carry out the work to code.
High ceilings and exterior work on tall structures can require elevated access. If scaffolding or a lift is needed for a particular job, we work that into the scope and discuss it on the call before scheduling.
In most cases, yes. If the work does not require the circuit feeding the refrigerator or freezer to be off, those appliances stay on. If the panel has to be de-energized for part of the job, we plan the shutdown to minimize the time those circuits are off.
A well pump runs on a dedicated circuit sized to the pump's motor draw, with a pressure switch and the correct disconnect at the pump location. We confirm the circuit requirements from the pump's specifications before running the supply.
It can, yes. Properties built in certain decades may have aluminum branch-circuit wiring, panels that are no longer manufactured or supported, or wiring that was installed before current GFCI and AFCI requirements existed. None of those conditions means the property is unsafe by definition, but each one changes what is involved in a repair or upgrade. The call is where we talk through what the property has and what that means for the scope.
We explain what the issue is, what the current code requires, and what the options are for bringing it into compliance. The repair path is agreed on before any work is done, and the finished installation meets the standard that applies to the property.
Older single-family properties in this part of Miami-Dade County often have panels and branch circuits that were sized for a lighter load than what a modern household draws. Common calls involve breakers that trip under normal use, outlets that have lost GFCI protection, and wiring that has not been inspected since the house was built. A diagnostic visit identifies the specific cause before any repair is quoted.
In most cases, the work inside a unit affects only the circuits on that unit's panel, so the rest of the building is not affected. If the job involves the building's shared electrical infrastructure, that is a conversation for the property manager or building engineer. We handle what is inside the unit and let you know on the call or on-site if the fault traces back to something outside it.
We clean up the work area before leaving. Tools, offcuts, and packaging are taken away, and the space is left in the condition we found it, aside from the work that was done.
Describing what the circuit is doing, or not doing, is enough to start the conversation. We take it from there.
Call (786) 926-3289 any day between 9:00 AM and 11:00 PM, and tell us what is going on. Pricing set out up front. Code-compliant work. Reliable power.
Have a look at our coverage area list. Electrical work also reaches these towns: Kendale Lakes, Westchester, The Hammocks, Coral Gables.
Every electrical job starts the same way: a call, a clear conversation about what is going on, and a price confirmed before anything is scheduled. The table below covers the full range of work we handle in Kendall and across Miami-Dade County. Use it to find the service that fits your situation, then call us and we will scope the job from there.
| Electrical Service | What It Covers | Ideal For | What to Keep in Mind |
|---|---|---|---|
| Electrical Panel & Service Upgrades | 200-amp panel upgrades, Fuse box replacement, Service entrance and meter work, Subpanel installation | Older homes adding major appliances, AC feeds, or EV chargers that the existing panel cannot support | A load calculation is part of every panel upgrade so the new service is sized to what the property actually needs. |
| Pool & Spa Wiring | Dedicated pump circuit, GFCI protection at pool outlets and fixtures, Bonding grid installation, Exterior pool area lighting | Kendall homes adding or updating a pool or spa where code-compliant wiring and bonding are required | Bonding connects metallic pool components to prevent voltage differences in the water. We handle the full electrical scope, not just the outlet. |
| Outlet & Switch Installation | GFCI outlet installation, AFCI protection, Dimmer and smart switch wiring, USB outlet installation | Kitchens, bathrooms, garages, outdoor locations, and any room needing updated receptacles or switch configurations | Code requires GFCI protection in wet and outdoor locations. We confirm what applies before the work is scoped. |
Call (786) 926-3289 and tell us what is going on. We will scope the job, confirm the price, and get it on the schedule.
(786) 926-3289