Electrical problems in a home or a business do not always announce themselves loudly. A switch that runs warm to the touch, an outlet that trips its GFCI every few days, a panel that hums when the air conditioning kicks on: these are the things that get noticed and then set aside. They are worth a call. We handle the full range of residential and commercial electrical work in Coral Gables, from a single circuit repair to a complete service upgrade, and the job is scoped on the phone before anything is scheduled.
Coral Gables is a city with a real mix of property types. Older homes carry wiring that was installed under different standards, and the work that comes out of them reflects that. Newer construction brings its own demands, from EV charger circuits to generator hookups. Whatever the property, we cover it.
Call (786) 926-3289 and we will talk through what is going on.
Some electrical problems can be scheduled around a normal week. Others cannot. An outlet that sparks when a plug goes in, a panel that will not reset, a circuit that cuts power to part of the building: those calls go to the front of the conversation. We are available every day from 9:00 AM to 11:00 PM, and short-notice work is part of what we take on.
Call (786) 926-3289, describe what is happening, and we will confirm what the schedule allows.
A rental property with a tenant in it, a business that has to stay open during the day, a building where access to the panel is shared: these situations come up regularly in Coral Gables, and the job is planned around them. The scope is confirmed on the call, including access requirements and any timing that matters. We protect your floors and finishes while we work, and the site is left the way we found it when the job is done.
You should not have to guess what the work will cost before anyone shows up. When you call, we talk through what is going on, and the price is confirmed before anything is scheduled. That is how it works for a straightforward repair and for a larger job alike.
What moves a quote is what the job actually involves. The fault itself is part of it. So is what has to be opened up to reach it, whether that means a finished wall, a ceiling, or a conduit run that was never documented. Whether the existing circuit or panel can carry the change also matters. A dedicated circuit for a new appliance, a subpanel addition, or an EV charger installation each starts with a panel capacity check, and the answer to that check shapes the scope. You get a plain answer on repair versus upgrade before any work begins, so nothing comes as a surprise when the job is underway. Pricing set out up front. Code-compliant work. Reliable power.
In Coral Gables, panels turn up in a range of locations depending on the age and style of the property. Older homes often have the panel in a utility room, a laundry area, or mounted on an exterior wall of the garage. Newer construction tends to put it in a dedicated electrical room or a mechanical closet. Wherever it is, clear access to the panel before the visit keeps the job moving. If furniture, stored items, or shelving are in the way, moving them ahead of time is the single most useful thing a property owner can do.
Beyond panel access, knowing which circuits are affected and whether the problem is consistent or intermittent gives us a head start. An outlet that only fails under load, a breaker that trips at a particular time of day, or a fixture that flickers only when another appliance is running: those details narrow the diagnostic before the visit starts. We service this area, and its neighborhoods each have their own wiring. The more a caller can describe on the phone, the faster the job moves once we are on-site. If you want the longer version, it is on our page listing every electrical service.
An outlet that has never worked since the house was bought. A switch that throws a small spark when it is flipped. An exterior light that has been out for two seasons. These are the jobs that get added to a mental list and stay there, because nothing has caught fire and the inconvenience is manageable. The problem is that each of them points to something real. A dead outlet can mean a failed GFCI upstream that is also protecting other receptacles. A sparking switch can mean deteriorated contacts or a loose connection inside the box. An outdoor fixture that stopped working may have lost its weatherproof seal, and the wiring behind it may have been exposed to moisture for longer than it looks.
None of these calls are complicated. Most of them are straightforward once they are looked at. The cost of leaving them is that the underlying condition does not stay static. Give us a call and consider it handled.
A panel with missing or incorrect labels is a practical problem every time a circuit needs to be isolated. We map the circuits, test each one, and label the panel accurately. In older properties, this often turns up double-tapped breakers or circuits that were added without being documented, and those findings are explained before any further work is quoted.
Intermittent faults are the hardest ones to track. A breaker that trips once a week, an outlet that works most of the time, a fixture that dims under load: these take a methodical approach rather than a quick swap of the obvious part. We trace the fault back to its source, check AFCI and GFCI protection where it applies, and confirm the fix before the visit closes.
An inspection covers the panel condition, the wiring type present in the property, grounding and bonding, and GFCI and AFCI protection placement throughout. Common reasons to schedule one include a pre-purchase review of an older home, a post-storm assessment, or a property that has not had its electrical system looked at in years. The findings are laid out plainly, and any repair path is explained before work is scheduled.
Older properties in this part of Miami-Dade County carry knob-and-tube wiring that was installed under standards that no longer apply. Replacing it means pulling new copper branch circuits and updating the panel to match the new load. The scope, whether partial or full, is determined by what is in the walls and what the property needs. Wiring work is checked against code before sign-off.
A ceiling fan installation is straightforward when an existing box is rated for the load. When there is no box, or the box in the ceiling is not fan-rated, we replace it and confirm the wiring before the fan goes up. Switch configuration, including three-way setups and dimmer compatibility, is confirmed as part of the job rather than left to the homeowner to figure out afterward.
Running power to a detached structure or an electric gate means a dedicated circuit from the main panel, the right conduit for the run, and correct grounding at the subpanel or disconnect on the far end. The capacity of the main panel is checked before the circuit is run. For electric gates, the circuit is sized to the gate operator's draw and the run is protected for outdoor conditions.
Yes. We cover Coral Gables and the surrounding communities throughout Miami-Dade County. Nearby areas we serve include South Miami, Pinecrest, Glenvar Heights, Coral Terrace, and Palmetto Bay. Residential and commercial work is handled across the area, and the process is the same wherever the property is: scope the job on the call, confirm the price, and carry out the work to code. One call gets the problem looked at properly.
We look at the panel's current capacity, the size of the main breaker, and how many slots are available before any new circuit is added. If the panel cannot carry the added load safely, we talk through an upgrade before scheduling the new circuit work.
The call is where the job gets scoped. You describe what is going on, we ask what we need to know about the circuit, the panel, and the property, and we give you a price before anything is scheduled. If the job turns out to involve something that changes the scope once we are on-site, we explain what changed and what it means for the price before proceeding. Nothing moves forward without your agreement.
We complete everything that can be done with what is on hand, secure any open work safely, and schedule the return visit once the part is available. The price for the full job is confirmed before we leave.
Older properties in this part of Miami-Dade County frequently turn up knob-and-tube or aluminum branch-circuit wiring, panels that were sized for a smaller load than the home now carries, and GFCI protection that was never installed in kitchens, bathrooms, or outdoor locations. These are not emergencies in most cases, but they are worth having looked at, because the underlying condition tends to develop rather than hold steady.
Call (786) 926-3289 and we will talk through what the property has and what it means.
The first step is confirming the scope from the call and taking a look at the panel and the area where the work is happening. That review sometimes turns up something that changes the scope slightly, and if it does, we explain it before any work begins.
A motor-driven appliance draws a surge of current at startup, and if the circuit or panel is already near capacity, that surge pulls voltage down briefly across the whole supply. Persistent dimming points to a load issue worth looking at, and we can assess whether a dedicated circuit or a panel upgrade addresses it.
Meter and service entrance work involves coordination with the utility, and we handle that side of the process as part of the job. The scope and the steps involved are explained on the call so you know what to expect.
The jobs that sit on the list the longest are rarely the complicated ones. They are the ones that seem manageable enough to leave until next week. The outlet, the switch, the exterior fixture, the panel that makes a sound it did not used to make: each of them has a straightforward answer, and the answer does not get simpler with time.
Call (786) 926-3289 to reach us.
We are available every day from 9:00 AM to 11:00 PM. We handle the work from the first call through to sign-off. You schedule it. We power it. Simple as that.
The rest are on our coverage area list. Electrical service reaches these neighboring areas too: Kendall, Westchester, Cutler Bay, Kendale Lakes.
Every electrical job starts the same way: a call, a clear conversation about what is going on, and a price confirmed before anything is scheduled. The table below covers the full range of work we handle in Coral Gables and across Miami-Dade County. Use it to find the service that fits your situation, then call us and we will scope the job from there.
| Electrical Service | What It Covers | Ideal For | What to Keep in Mind |
|---|---|---|---|
| Electrical Panel & Service Upgrades | 200-amp panel upgrades, Fuse box replacement, Service entrance and meter work, Subpanel installation | Older homes adding major appliances, AC feeds, or EV chargers that the existing panel cannot support | A load calculation is part of every panel upgrade so the new service is sized to what the property actually needs. |
| Outlet & Switch Installation | GFCI outlet installation, AFCI protection, Dimmer and smart switch wiring, USB outlet installation | Kitchens, bathrooms, garages, outdoor locations, and any room needing updated receptacles or switch configurations | Code requires GFCI protection in wet and outdoor locations. We confirm what applies before the work is scoped. |
| Dedicated Appliance Circuits | Dryer and range circuits, Refrigerator and washer circuits, AC supply-side circuit, Workshop and garage circuits | Any major appliance or equipment that needs its own circuit sized to the load | We handle the electrical supply side for AC units: the dedicated circuit, the disconnect, and the panel capacity check. The unit itself is outside our scope. |
Call (786) 926-3289 and tell us what is going on. We will scope the job, confirm the price, and get it on the schedule.
(786) 926-3289